Skip to main content
Roof Report Pro
Back to Blog
Guides

Roof Inspection Checklist by Roof Type

The roof inspection checklist by roof type: six surface items each for metal, tile, flat, slate, wood shake and shingle roofs, and what each photo shows.

RRPT
Roof Report Pro Team
November 18, 2026
16 min read
Last reviewed Nov 18, 2026

A roof inspection checklist changes by roof type in one place only. The stages before and after the roof surface stay the same on every roof. The surface stage swaps to six items written for the material: shingle, metal, tile, slate, wood shake or flat membrane. Each set tells you what to photograph and what that photo establishes.

Inspectors who work more than one material learn this the hard way. A shingle routine does not carry over to a standing seam roof, and a metal routine tells you nothing useful about a tile roof. The material decides where water gets in, how damage shows up, and which photo makes the finding hard to argue with.

Key takeaways:

  • Eight stages run in the same order on every residential roof. Only the roof-surface stage changes.
  • Every surface set has six items. The first is always a wide overview of the slope or plane, so every close-up can be placed on the roof.
  • Impact damage reads differently on each material: a hit on a shingle, a dent on metal, a spall on tile, a bruise on a membrane. Each set tells you how to light and frame it.
  • Every surface set ends with an identification item, because a report that names the material exactly is easier to act on.
  • A roof with more than one surface type carries more than one set.

What stays the same on every roof type?

Before you ever pick a surface set, the inspection is already underway. The inside-out checklist runs in eight stages, and the roof surface is only one of them. The others cover the interior and attic, the ladder-assist shots at the eave, soft metals and collateral, gutters and downspouts, flashing, elevation overviews and a closing stage for other roof detail. None of those change when the material changes. A cracked boot, a dented vent hood and a wet attic ceiling look the same under a tile roof as under asphalt.

That is why this guide does not re-explain them. The full walk-through of each stage lives on the roof inspection checklist, and the reasoning for working from the attic outward is in inside-out roof inspection. Read those first if you have never run the sequence. What follows is the part that does change: the six items in the roof-surface stage.

Two practical notes before the material sections. First, the surface stage is worked one slope at a time, and each slope gets the same shots in the same order. The app labels slopes Front, Right, Rear and Left by default, and the overview, the close-ups and the identification shots hang off those labels. Second, the slope overview comes first on every roof type, and it is required. It fixes the slope in the record and shows the penetration count, so nobody has to guess later which close-up belongs to which part of the roof.

How do the six surface sets compare?

The table lists every item in every set, in the order you shoot them. Notice the pattern: overview first, then the breach or opening in the water path, then the impact damage, then wind, moisture or edge conditions, and last the identification shot.

Roof typeItem 1Item 2Item 3Item 4Item 5Item 6
Asphalt shingleSlope overviewTest squareHail close-upsWind damageLift checkManufacturer ID
MetalSlope overviewSeams and fastenersHail dents on panelsWind uplift and edge metalCoating and corrosionManufacturer / profile ID
TileSlope overviewCracked / slipped tilesHail strikes and spallingUnderlayment and valleysHip / ridge mortarManufacturer mark (underside)
SlateSlope overviewBroken / missing slatesHail strikes and delaminationNail sicknessFlashing and valley solderSlate thickness sample
Wood shakeSlope overviewSplitting and cuppingHail impact and fiber lossMoss / rot / decayKeyway and interlaymentGrade / thickness sample
Flat membraneRoof plane overviewSeams and terminationsPonding and drainageHail bruising and puncturesPenetrations and curb flashingMembrane ID plate

Asphalt shingle roof inspection checklist

Shingles are the baseline most inspectors learned on, so the set reads like a routine you already know. The instruction for the whole stage is to work one slope at a time using the same four shots each time, until the sequence is muscle memory. You do not count hits yourself. The analysis counts them inside the frame, so your job is to produce frames that can be counted.

1. Slope overview. Shoot the full slope wide before any close-up. This photo establishes the slope and its penetration count, so every close-up that follows can be mapped to a location. Stand where the whole plane fits, keep the ridge and eave both in frame, and do the same on every slope. It is a required item, and it is per slope.

2. Test square. Chalk a ten by ten foot square, circle each hit inside it, number the hits and keep all four corners in frame. The photo establishes the hit density on a defined area in a way anyone can recount from the picture. Corners in frame is the detail people skip. Without them, the square could be any patch of roof. A standard report does not include this item, which is covered below.

3. Hail close-ups. Get in close on the worst hits, square-on, with chalk beside them for scale and out of harsh shadow. The close-ups of the best hits show fracture and mat exposure, which is the functional damage that separates a real hit from a surface scuff. Shooting square-on matters because an angled shot hides the depth of the bruise. Wait for the light to even out, or shade the spot with your body.

4. Wind damage. Draw a chalk line along each creased or lifted tab, then shoot it. Lifted, creased and unsealed tabs on each slope document wind separately from hail, so keep the two sets of photos apart. The chalk line is what keeps a creased tab from disappearing into the pattern of the roof. This item is optional, since not every slope has any, but when it does the marking is what makes the photo readable.

5. Lift check. Flex a tab at the edge and capture the crack or fold as a photo or a short video. The photo establishes the condition of the shingle material itself, which is useful context for every other finding on the slope. Do it where it can be done safely, in a spot that will not show on the finished roof, and note the air temperature, since a cold shingle behaves differently than a warm one.

6. Manufacturer ID. Flip a shingle for the back-branding, or shoot a wrapper if one is on site. The branding identifies the manufacturer and product, which is what lets anyone later specify the right material. A wrapper in the dumpster is as good as a printed back, so look around the job site before you leave.

Metal roof inspection checklist

Metal changes the picture because the panel is usually undamaged in the way a shingle would be damaged. A hail hit does not fracture anything. It leaves a dent, and the dent is the evidence. Meanwhile, the weak points are the fasteners, the laps and the edge metal, which are not part of the shingle routine at all. The stage instruction: work one slope at a time, shoot the slope wide, then the seams and fasteners, then get in close on the dents.

1. Slope overview. Shoot the full slope wide before any close-up. The photo establishes the slope, its panel run and its penetration count, so every close-up maps to a location. On a long panel run, stand back far enough that you can count panels from eave to ridge.

2. Seams and fasteners. Walk each seam and shoot straight down on any backed-out fastener or opened lap. Backed-out fasteners, failed washers and opened seams are the metal equivalent of a lifted tab: a functional failure rather than a cosmetic one. Shooting straight down matters, because a shot at a shallow angle makes a raised screw head look flush. Where the roof is exposed-fastener, work down the screw lines; where it is standing seam, work the seam itself.

3. Hail dents on panels. Shoot the panel with light raking across it so the dents cast a shadow, with something for scale. Dents in the flat of a panel establish impact severity. On metal the dent is the damage, so a raking-light frame is what the analysis reads. A dent shot with the sun straight overhead can look like nothing at all. Move low, let the light come across the panel from the side, and put a scale reference in the frame.

4. Wind uplift and edge metal. Shoot along the rake and eave so any lift, separation or deformed clip is visible in profile. Lifted panels, deformed clips and peeled edge metal document wind separately from hail, and edge metal is where uplift starts. Profile is the key word. A shot looking down at an eave edge flattens the very gap you are trying to show.

5. Coating and corrosion. Get in close on any chalking, blistering or rust bleed, especially where a dent broke the coating. The photo establishes whether the panel has lost its protective layer. A dent with an intact finish and a dent with exposed substrate are two different conditions, and the close-up is how a reader tells them apart.

6. Manufacturer / profile ID. Shoot the panel profile end-on, then any stamp, label or stencil on the underside or in the ridge. The profile plus a maker mark identify the system, which is what lets a reader find the manufacturer's own installation and repairability bulletins. The end-on view shows the rib shape and gauge more clearly than any angle across the panel.

Tile roof inspection checklist

Tile is heavy, brittle and often walked only with care, and the set reflects it. The stage instruction asks you to walk it only where you can walk it safely, and to work one slope at a time: the slope wide, then every cracked or slipped tile, then close on the spalling. The tile itself is only half the system. The underlayment beneath it does the waterproofing, which is why two of the six items look below the field.

1. Slope overview. Shoot the full slope wide before any close-up. It establishes the slope, its coursing and its penetration count. With tile, the coursing lines make a useful grid, so keep them straight in the frame.

2. Cracked / slipped tiles. Shoot each cracked or slipped tile square-on with the surrounding courses in frame for position. A cracked or slipped tile is a breach in the water path. Keeping the surrounding courses in frame tells the reader where in the roof the tile sits, and square-on shows the crack running through, not just across, the tile.

3. Hail strikes and spalling. Get in close on the freshest spall marks with chalk beside them for scale, out of harsh shadow. Hail on tile spalls the surface and exposes the body beneath, so the marks are the tile counterpart of mat exposure on a shingle. Fresh marks look lighter and cleaner than weathered ones, which is why the instruction says to go for the freshest.

4. Underlayment and valleys. Lift a tile where you safely can, or shoot down the valley, so the underlayment condition is visible. On a tile roof the underlayment is the actual waterproofing layer, and the valley is where its condition decides whether the roof is still serviceable. Do not lift tiles you cannot put back, and do not lift them on a roof you cannot stand on.

5. Hip / ridge mortar. Walk each hip and the ridge and shoot any cracked, loose or missing mortar. Cracked or missing mortar lets wind under the coursing, and it is priced and repaired separately from field tile, so it deserves its own photos rather than a mention in the overview.

6. Manufacturer mark (underside). Lift one field tile and shoot the underside so any stamped name, mould number or date is readable. Most tile carries a maker mark underneath. It identifies the profile and the production run, which is what lets a reader cite the manufacturer's own bulletins. This is the single most useful identification shot on a tile roof, and it takes thirty seconds.

How do you inspect a slate roof?

Slate is the material where the field is the most fragile and the age is the longest. The stage instruction says to shoot from a ladder or a lift rather than walking the field, and to work one slope at a time from the edge: the slope wide, then every broken or missing slate, then the strikes. Slate has no manufacturer on its back, so the set replaces the identification shot with a physical sample.

1. Slope overview. Shoot the full slope wide from the edge or a lift before any close-up. It establishes the slope, its coursing and its penetration count.

2. Broken / missing slates. Shoot each broken or missing slate square-on with the surrounding courses in frame for position. A broken or missing slate is a breach in the water path and the most direct finding on a slate roof. Record the course it sits in, because the repair is planned course by course.

3. Hail strikes and delamination. Get in close on the strikes with chalk beside them for scale, out of harsh shadow. Hail on slate leaves a bruise that delaminates, and fresh breakage at the strike is what separates storm damage from age. Look for sharp, bright edges rather than rounded, weathered ones, and frame so that the difference shows.

4. Nail sickness. Shoot any slipped slate and the exposed nail or nail hole above it. Corroded nails let sound slates slip, so the slate itself is fine while the fixing has failed. Documenting it decides whether the roof is repairable at all or whether the fixings are failing across the slope. It is flagged as an integrity concern in the checklist for that reason.

5. Flashing and valley solder. Shoot down each valley and along the step and counter flashing so any open joint is visible. Open solder joints and failed valley metal are where a slate roof leaks long before the field does, and they are priced separately from the slate.

6. Slate thickness sample. Shoot the edge of a loose or removed slate against a tape or coin so the thickness reads. There is no manufacturer to cite, so the physical sample is the identification. Thickness and quarry character set the grade, and the grade sets the replacement specification.

What should you look for on a wood shake roof?

Cedar ages visibly, and that is the difficulty. A shake roof is always weathered, so the set is built around telling storm damage from wear and showing both honestly. The stage instruction: work one slope at a time, shoot the slope wide, then the splits and cupping, then get in close on the impact points.

1. Slope overview. Shoot the full slope wide before any close-up. It establishes the slope, its coursing and its penetration count.

2. Splitting and cupping. Shoot along the coursing so the split shakes and any cupped butts read against the plane. Splits and cupping open the keyways and lift the butt ends. It is the condition the whole shake assessment runs through, so it is documented per slope, and low raking angles along the course show the lifted butts best.

3. Hail impact and fiber loss. Get in close on the brightest impact points with chalk beside them for scale. Hail on cedar tears fiber and leaves a bright, unweathered impact point. That colour break is what dates the damage: a bright mark on grey wood happened recently, and the photo can show it.

4. Moss / rot / decay. Shoot the worst decay and moss, and a clean course nearby for comparison. Wear is part of every shake roof. Documenting where it is, and where it is not, keeps the storm findings from being lumped in with age. This item carries an integrity-concern tag, and the comparison course is what makes it fair.

5. Keyway and interlayment. Shoot down a keyway so the offset below it and any interlayment felt are visible. Keyway alignment and the interlayment felt beneath decide whether water reaches the deck, and both are per slope and both are priced.

6. Grade / thickness sample. Shoot the butt end of a loose or removed shake against a tape or coin so the thickness reads. Cedar has no manufacturer, so the physical sample is the identification: the grade and the butt thickness set the replacement specification.

Flat and low-slope membrane roof inspection checklist

Flat roofs fail differently. Water does not run off quickly, so every breach and every low spot matters more. The membrane set has its own wording at the top: seams and terminations, ponding and hail bruising are the findings that matter most on a low-slope roof, and the bruising in particular is often invisible from a distance and only reads in a raking-light close-up. The stage instruction: shoot the plane wide, then walk every seam and termination, then get in close on the bruises with light raking across them. Note that this set calls the first item a roof plane overview, not a slope overview.

1. Roof plane overview. Shoot the full plane wide from one corner before any close-up. The photo establishes the plane, its equipment and its penetration count, so each close-up can be mapped to a location. On a large roof, shoot each plane from the same corner every time.

2. Seams and terminations. Walk every seam and termination and shoot straight down on any lift, void or pulled bar. An opened seam or a pulled termination bar is a direct breach. On a membrane roof it is the failure that is hardest to put down to age. Straight down shows the void; an oblique shot hides it.

3. Ponding and drainage. Shoot each ponded area with a drain or scupper in frame so the drainage path is visible. Standing water speeds up every other failure and points at drainage the roof no longer achieves. Showing the drain in the same frame as the water is the whole point: it ties the pond to the path water should take.

4. Hail bruising and punctures. Get low with light raking across the surface so the bruises cast a shadow, with chalk beside them for scale. Hail bruises a membrane without breaking it. The bruise is invisible head-on and only reads in raking light, which is why the shot is specified instead of left to judgement. Early morning and late afternoon do half the work for you.

5. Penetrations and curb flashing. Shoot each curb and pipe boot with its flashing and any cracked sealant in frame. Curbs, pipe boots and equipment penetrations are where a low-slope roof leaks first, and they are priced separately from the field of the roof.

6. Membrane ID plate. Find the ID plate at a curb or the roof hatch and shoot it close enough to read. The plate names the system and the thickness, which lets a reader cite the manufacturer's own repairability bulletin and answer whether a patch is permitted. If you cannot read it in the photo, shoot it again.

What if one property has more than one roof type?

Plenty of houses do. A tile main roof with a flat membrane over a rear addition, or a shingle roof over the house and a metal roof over the porch. The app lets one report carry several surface sets, so each surface gets its own six items instead of being forced into one list. In practice, work the property by surface: complete the surface stage for the main roof, then do the same for each additional surface, and keep each surface's photos under its own set.

The stages before and after the surface stage run once for the whole property. You do not repeat the attic, the eave shots, the flashing or the elevations for each material. Where a flashing detail sits at the junction of two surfaces, such as a wall that rises from a flat roof into a shingled one, shoot it once in the flashing stage and mention both surfaces in the note.

What about multi-family roofs?

Multi-family reports have their own structure and do not use the six-item residential sets. They carry a steep-slope exterior stage and a low-slope exterior stage, each with its own list of observations written for larger buildings, including roof membrane, expansion joints and drainage systems on the low-slope side. If you inspect apartment buildings, use the multi-family sets for those and the residential sets in this guide for houses and townhomes. The checklist-based inspections feature page shows how the app presents the sets.

What does a standard report leave out?

Not every report is a full inspection. A standard report uses a shorter set of stages and items. It leaves out the attic stage, the ladder-assist eave shots, the flashing stage and the soft-metals stage, and it hides some items inside the roof-surface set. On shingles, the hidden items are the test square, the lift check and the manufacturer ID. The same logic applies to the identification items on the other surfaces: the metal profile ID, the tile underside mark, the slate thickness sample, the shake grade sample and the membrane ID plate are all left out of the standard set.

Wind inspections also drop one stage. They skip the soft-metals stage, since that stage is about hail marks on collateral metal.

None of this makes the shorter set wrong. It makes it shorter, and you should know which one you are running before you climb. If the roof turns out to need the extra photos, it costs less to take them while you are standing there than to come back.

Common mistakes when switching roof types

Three errors repeat. The first is carrying the shingle habit to every roof: chalking a test square on a metal roof and counting nothing useful, or hunting for hail hits on a membrane when the bruising only shows in raking light. The second is skipping the identification item because it feels like paperwork. It is the one photo that lets a reader find the right bulletin or specification months later. The third is lighting. On metal, membrane and shake, the light angle decides whether the damage exists in the picture at all.

These and others are covered in common roof inspection mistakes. If you are bringing new inspectors up on several materials, how to train a roof inspector lays out a sequence that teaches the material sets one at a time.

A short field routine for any roof type

Whatever the material, the routine for the surface stage is the same shape. Start with the overview of the slope or plane, wide, from the same place every time. Shoot the openings in the water path next: the cracked tile, the missing slate, the opened seam. Move to impact damage, using chalk for scale and a low light angle where the material needs it. Document wind, decay or edge conditions on their own. Finish with the identification shot. If you do the six items in order, on every slope, you will not forget one.

Then move on to the next stage and let the rest of the checklist carry you.

roof inspection checklist
roof types
metal roof
tile roof
flat roof
inspection photos
Share this article:

Frequently Asked Questions

Related Articles

Guides

Complete Guide to Roof Inspections in 2026

A step-by-step guide to roof inspections: equipment, process, damage identification and photo-backed reports that are clear and easy to read.

Read more
Guides

How to Document Roof Damage After a Storm

The exact photos, notes, and timelines that make roof damage documentation clear, organized, and complete. A practical guide for homeowners.

Read more
Guides

Roof Inspection Report Template: What to Include

Free roof inspection report template with 8 clear sections. Download it, see real examples, and start producing clearer reports.

Read more

Related Features

Ready to Try Roof Report Pro?

Start creating professional inspection reports with AI-powered analysis.

Start Free Trial
See the deliverable

View real Roof Report Pro reports — and share them

A standard report for the homeowner and a detailed forensic report, from the same inspection. No account needed.

View the sample report onlineor share this link with others so they can see it as well
roofreportpro.app/0yKEOu7aRgVZlGmA