A Roof Record That Reads the Same Every Time
For property-insurance attorneys: a staged roof inspection checklist, photos tied to checklist items and roof sections, capture dates, and a detailed report signed by the inspector of record.
Last reviewed Nov 18, 2026Eight
Inspection stages1
Inspector of recordSoon
Expert reportChallenges You Face
We understand the problems that slow you down
Photos Without Sequence
A camera roll holds two hundred roof photos in the order the inspector happened to walk the roof. A reviewer cannot tell which slope a picture shows, what came before it, or what the photographer meant it to show. The file depends on the memory of whoever was there.
Close-Ups With No Overview
A tight image of one damaged shingle says little without a wider frame that places it on the roof. When that frame is missing, location is taken on trust, and a reader who cannot place a picture has to ask for another one.
Interior Evidence Left Out
Many roof visits begin at the ladder. The attic, the underside of the decking and any staining below the roof then go unphotographed, and the file describes only what could be seen from above.
No Record of What Was Not Found
A report that lists only damage says nothing about the items the inspector looked for and did not find, or skipped. Counsel cannot tell an item that was checked and clear from an item nobody checked.
Every File Built a Different Way
When each inspector organises a file as they see fit, a reviewer handling many matters relearns the layout every time. The hours go on finding things rather than reading them.
How Roof Report Pro Helps
Roof Report Pro gives attorneys a staged roof inspection checklist, photos tied to checklist items, capture dates and a detailed report signed by the inspector.
Eight-Stage Checklist
The inspection runs inside out in a fixed order: attic and interior, ladder assist, soft metals and collateral, gutters and downspouts, flashing, the roof surface, elevation overviews and a closing stage for other roof detail. Wind-only inspections leave out the soft metals stage. Read the full checklist.
Photos Tied to Checklist Items
Each photo is attached to the checklist item it answers and to the roof section it shows, so a reader can go from a picture to the question it was taken to answer.
Capture Dates on Photos
A photo is stored with the time it was taken when the phone or camera file provides one. A photo that arrives without that information has no capture time to store.
Inspector of Record
A forensic report is signed by the inspector of record, the person who ran the inspection and reviewed the findings. The document names who stands behind it. The forensic report is being rolled out and may not be selectable in every account yet; ask us what is available today.
Skipped Items Recorded
When an inspector skips a checklist item, a reason goes in with the skip. The file shows which items were completed and which were not, side by side.
Summary of Findings and Repair Scope
Each roof section carries its own photos, markers and notes, so a reader can open the slope or component in question without paging through the rest. The report summarises the documented findings and repair scope section by section.
Edit History
A change to a finding is logged with the person who made it and the time, and the original AI reasoning stays beside any inspector override.
Detailed Forensic Report
Methodology, findings by roof section, captioned photos, and cited building codes and manufacturer specifications, signed by the inspector of record. See forensic reports.
Comparison With Prior Findings, Coming Soon
An Expert report prepared for counsel from an existing inspection record, laying the documented conditions next to prior findings point by point. It is coming soon and cannot be ordered yet.
Real-World Use Cases
See how professionals like you use Roof Report Pro
Reviewing Who Documented a Roof, and When
A legal team receives a roof file and needs to know when the photos were taken and by whom before relying on any of it.
The record names the inspector of record, shows each photo with its capture time where the file provided one, and shows the edits made to the report afterwards.
Tracing One Finding Back to Its Photos
Counsel wants to understand how a report reached a statement about one slope.
The finding sits with its photos and markers under that roof section. The checklist item each photo answers is named, and the original AI reasoning is kept beside any override.
Reading Many Files From Many Inspectors
A practice reviews roof files from several inspectors over a season.
A full inspection has the same eight stages in the same order (a wind-only inspection leaves out the soft-metals stage, and the shorter standard report uses fewer), so the reviewer spends the time on the findings and not on finding the layout.
With vs. Without Roof Report Pro
| Aspect | With Roof Report Pro | Without |
|---|---|---|
| Photo order | Fixed stage order, inside out, overview before close-ups | Whatever order the camera roll recorded |
| Photo context | Tied to a checklist item and a roof section | A pile of images with no label |
| Items not found | Skips recorded with a reason | Silence about what was not checked |
| Report changes | Edit history with author and time | Final document only |
| Author | Signed by the inspector of record | Unclear who prepared and reviewed it |
Frequently Asked Questions
What Counsel Needs From Roof Documentation
A lawyer reading a roof file wants a handful of plain answers without calling anyone. The reader may act for a policyholder, for a carrier, or for the other party to a coverage dispute, and each needs the same plain facts. Where a policyholder believes a loss was underpaid, the roof file is one of the documents a reviewer reads. Who inspected the roof? When were the photos taken? Which parts of the roof were looked at, and in what order? What was found on each, and what was looked for and not found? Where is the picture behind each statement? A file that answers those questions can be reviewed quickly and reviewed again by a colleague. A file that does not forces a round of requests, and every request costs time on a matter that already has deadlines. Roof Report Pro is organised around those questions. The inspection follows a checklist, the checklist ties every photo to an item and a roof section, and the report is arranged so a reader can go from a sentence to its evidence. The rest of this page describes what that record contains and what it does not.
Why Inspection Files Are Usually Thin
Most thin roof files are thin for structural reasons. The inspector was capable and the roof was real, but the way the visit was run left holes. Photos were taken as the inspector moved, so the sequence reflects a walking route rather than a logic a reader can follow. Close-ups have no overview, so the location of each is a matter of trust. The attic was skipped because the visit started at the ladder, which means there is no interior evidence at all. The manufacturer's identification was never photographed, so the product is a guess. And nothing says what was not found: the report lists what was seen and stays silent about the rest, which leaves a reviewer unable to tell a clear item from an unchecked one. This is the file a reviewer inherits when a denied claim reaches counsel, or when a reopened claim needs the original visit reconstructed. Each of these holes is cheap to avoid when the visit is structured and costly to repair afterwards, because repair means another trip to the property.
The Documentation Trail the Product Keeps
Roof Report Pro keeps a trail that a reviewer can read without the inspector present. A full inspection is completed in the eight stages of the checklist, in a fixed order. Each photo is attached to the checklist item it answers and to the roof section it shows. Each photo is stored with the time it was taken when the phone or camera file provides that information. The inspector of record is named on the forensic report. When a checklist item is skipped, the skip is recorded with a reason. Changes to findings are logged with who made them and when, with the original AI reasoning kept beside any inspector override. And the structure is the same on every file. None of this is a legal chain of custody and the product does not claim to be one. It is a set of facts a reviewer would ask about, kept in one place, and counsel decides what weight each carries.
Eight Stages, Inside Out, in a Fixed Order
The checklist runs inside out. It begins in the attic, moves to a ladder at the eave, then to soft metals and collateral, gutters and downspouts, flashing, the roof surface, the elevation overviews, and a closing stage for other roof detail. Wind-only inspections leave out the soft metals stage. The order exists so that the evidence which does not depend on the weather that day is captured first and the large roof-surface work comes once the baseline is in the file. The inside-out walkthrough explains the reasoning for each step. The checklist was developed with property-insurance attorneys. Standard reports use a shorter set that leaves out some stages, and multi-family roofs have their own steep-slope and low-slope sets, so the full eight-stage sequence applies to a full or forensic inspection of a residential roof.
What Each Stage Gives a Reviewer
The attic stage gives a reviewer evidence from inside the building: staining on the underside of the decking, and the decking material, board direction and gaps. The ladder stage gives the baseline at the eave, such as the layers at the cut edge, edge underlayment and drip edge. The soft metals stage gives surfaces that record impacts distinctly from shingles, with each item photographed close and with something for scale. Gutters and downspouts add another run of surfaces, with their condition and size recorded. Flashing gives the places where the roof meets walls, chimneys and valleys, or a note that none is present. The roof-surface stage works one slope at a time, with a wide view before any close-up, a marked test square, a record of whether tabs lift, and a photograph of the manufacturer's identification. The elevation stage gives one view of every face of the building and the address, which anchors every close-up to a real property. The closing stage collects whatever else the inspector saw. Together they give a reviewer a path through the roof that is the same on each file.
Capture Dates and the Inspector of Record
Two facts matter to nearly every reviewer: when and who. For when, each photo is stored with the time it was taken whenever the phone or camera file carries one. The record therefore shows when the roof was documented, not only when the report was written. A photo that arrives without that information has no capture time to store, and the file does not invent one. For who, a forensic report is signed by the inspector of record. That person ran the inspection, reviewed the drafted findings and answers for the report. Roof Report Pro does not verify an inspector's qualifications or licence, so those are questions for the inspector. What the product does is make sure the person is named and that changes to the findings after the inspection are logged.
Skipped Items and the Record of What Was Not Found
A record of what was not examined, and why, is part of the file. A file that records only positive findings cannot answer. In the checklist, a skipped item carries a reason entered by the inspector, so the record shows what was checked and found clear, what was checked and found damaged, and what was left out and why. A section the inspector could not reach, a roof too steep to walk, a stage that did not apply to a wind-only inspection: each of those appears as a recorded decision rather than a gap discovered later. That does not make the inspection complete, and it is not meant to. It makes the extent of the inspection visible: what was examined, what was skipped, and the reason recorded for each.
Why Consistency Across Inspectors and Files Matters
A practice that reviews roof files rarely sees one inspector's work. It sees many inspectors, many roofers and many years of habit. When every file is organised differently, the first twenty minutes of each review go on learning the layout, and the same questions get asked again about the test square, the manufacturer's identification or the attic. A fixed checklist removes that overhead. Two properties will never look alike, but their files will have the same stages in the same order with the same items photographed. The reviewer knows where to look. A missing item shows up as a missing item. Comparing two files from different inspectors becomes a comparison of roofs rather than of filing styles. The file is often read later by people who were not on the roof; a consistent layout makes it quicker to find things. When a finding is questioned, the reader can go back to the photo and the checklist item behind it. For a firm with a large caseload, that predictability is the practical benefit, and it is a benefit of structure, not of any particular inspector's skill.
The Forensic Report as Detailed Documentation
The detailed document built from an inspection is the forensic report. It sets out the methodology, meaning how the inspection was run and in what order. It presents findings by roof section, each with its photos and captions that name the checklist item each picture answers. It cites building codes and manufacturer specifications against the findings they relate to. And it is signed by the inspector of record. The standard report is written in plain language for the property owner; the forensic report is the one meant for a reader who wants the method and the references. Every forensic report carries one fixed statement about its limits: Signed by the inspector of record. It is not an engineering opinion or legal advice. A reader should treat it as documentation of what the inspector found and cited, nothing more.
What the Software Is Not
Roof Report Pro is documentation software. It does not give legal advice and nothing on this page is legal advice. It does not reach a causation or structural conclusion, and it does not replace an engineer; where a matter needs a structural conclusion, that is a separate engagement. It does not interpret a policy and it does not say whether anything is covered. It does not act on any matter, speak to any carrier or party, or appear anywhere on anyone's behalf. It does not predict how a document will be received by any reader or tribunal, and it makes no evidentiary claim: whether a photograph or report is useful as evidence is for counsel. The inspector of record, not the software, is the person who made the findings and can explain them. The findings in a report are the inspector's findings, reviewed and signed by the inspector. The software contributes structure, photographs tied to checklist items, dates and a change log, and counsel decides what to do with them.
Working With the Roofer or Public Adjuster Who Did the Inspection
In most matters the person who documented the roof is not your colleague. It is a roofer, or a public adjuster, who ran the inspection in their own account before you were involved. Because every report follows the same structure, you can judge its completeness quickly: is the attic stage present, is each close-up paired with an overview, are there skipped items and why. You can then ask the inspector of record the specific questions the file raises. Public adjusters use the same checklist and report structure, so a file from one of them reads the same way. Inviting a roofer or adjuster to document directly with you is planned and is not available yet. Every report needs a Pro seat. Whoever produces the report needs the seat, so a firm that wants to run an inspection itself needs one too.
The Expert Report Is Coming Soon
The Expert report is a report prepared for counsel from an inspection record that already exists. It is coming soon and cannot be ordered today. It is planned to contain an Executive Summary, Materials Reviewed, Factual Background, Building Code Analysis, Manufacturer Warranty Analysis, Statutory & Regulatory Analysis, Weather Correlation (where available), Conclusions and an Appendix. Because it starts from an existing record, a good inspection file is the first requirement. That is why this page concentrates on the inspection record: it is available now and is what any later report would draw on. The Expert reports page describes the planned report and the reports overview compares it with the Standard and Forensic reports.
Questions Worth Putting to Any Roof File
Whatever the source of a roof file, the same short list of questions shows what the file contains. Is there an overview for each close-up, so that location is visible rather than asserted? Is the attic stage present, and if not, is there a recorded reason? Is each photo attached to a checklist item and a roof section, so that a statement in the report can be walked back to its picture? Do the photos carry capture times, and do those times fall inside a single visit or across several? Is the inspector of record named, and did that person sign? Are the skipped items listed, with reasons, or does the file stay silent about them? Is the manufacturer's identification photographed? Does the report cite codes and specifications against particular findings, or only mention them in general terms? A file built on the checklist answers most of these by its structure, and the answers that come back negative are visible as such. Those questions are also a fair way to put a file from any other source through the same test, since they do not depend on the software that produced it.
Traceable Sources for Every Quoted Provision
A reader checking a roof report will want to know where a quoted provision came from. In the forensic report, each quoted code or standard comes from a reference library entry with a recorded source, and the text is quoted from that entry rather than composed by the AI. Entries are matched to the property by jurisdiction and by the code edition in force on the date of loss, along with the damage types found in the photos and the product brand the inspector confirmed. The AI that writes reports has no web search or browsing, so it does not browse for other material. It works from the inspection's photos, the inspector's answers and the matched entries. The forensic report is being rolled out and is not selectable in every account yet.
How to Start
The easiest way to judge the record is to read it. Start with the full checklist to see each stage and what it asks for, then the forensic report page to see how findings are arranged. If you work with roofers or adjusters, the inside-out guide is useful to send them, since it explains why the file is in the order it is. To discuss your practice, or to hear when the Expert report opens, talk to us through the contact page.
Related Industries
Explore how other professionals use Roof Report Pro
Talk to us about your practice
Tell us how your firm reviews roof files and we will walk you through the record. Expert reports are coming soon.
View real Roof Report Pro reports — and share them
A standard report for the homeowner and a detailed forensic report, from the same inspection. No account needed.