A hail map for roofers that goes down to the house
A hail map for roofers shows where hail fell, how big it was and which houses sat under it, and Roof Report Pro's map does that for Florida and Texas with swaths, size filters from 1 to 2.5 inches and a history window from today back three years, plus wind filters at 50, 60 and 75 mph.
Key Statistics
Key Benefits
Hail map for roofers in Florida and Texas: hail swaths, size filters from 1 to 2.5 inches, history windows up to three years and wind filters by speed.
Hail swaths drawn over the street map
Each storm leaves a footprint, and the map draws it as a swath you can pan across. You see the heart of the storm and its ragged edges, which is where a rep decides whether a neighbourhood is worth the drive.
Four hail size presets
Filter to hail of 1 inch, 1.5 inches, 2 inches or 2.5 inches and up. Smaller stones are common and often do little to a sound roof, while the larger presets narrow the map to the houses under the most serious part of a storm.
A window from today back three years
Choose how far back to look. A narrow window answers last week's storm, and the wide one surfaces older hail that nobody has worked yet. The hail history behind the map starts in October 2020.
Wind at 50, 60 or 75 mph and up
Wind has its own filter with three speed presets, plus a wind zones overlay on the map. Pair it with hail and you can find houses that took both, or work a wind event where no hail fell at all.
Colour the whole map by hail or by wind
Instead of filtering, you can colour the homes in view by their hail or wind reading and look for gradients. A smooth fade at the edge of a swath tells you something a hard filter cut cannot.
Open a house for its own storm history
The home panel lists the hail and wind history for that address, along with tornado and hurricane proximity. A rep can read it on the porch, then check permits to see whether the roof has been replaced since.
How the Hail and Wind Map Works
- 1
Turn on the hail or wind layer
Open the layers and switch on hail, wind or both. The storm filter rows appear in the filter panel only once a layer is on, so the panel stays short until you need it.
- 2
Pick a size or speed, then a window
Click a hail size preset and a time window, or a wind speed preset. Nothing is typed, and the active choices stay on screen for the rest of the team to see.
- 3
Narrow with year built, permits and type
Add a build-year range, the roof permit filters or a property type. The live count tells you how many homes match in view, and counts under five are withheld.
- 4
Draw it as a territory and send the team
Outline the area, assign it to a rep or a crew, and let them work it from the app in a mobile browser. Export the addresses if the phone team needs the same list.
Real-World Use Cases
See how roofing professionals use this feature in their daily work.
The first dry morning after a Texas storm line
Scenario
A line of storms crossed a Texas metro overnight. The manager turns on the hail layer, sets the window to the last few days and clicks the 1.5 inch preset to see where the larger stones landed.
Outcome
Two suburbs light up. The team splits them into territories and the reps are on the right streets before lunch.
Finding the hail nobody worked last spring
Scenario
An owner in Florida has a quiet month. He widens the window to three years, picks 2 inches, then adds a build-year range and removes homes with a roof permit since the storm.
Outcome
He builds a list of houses that took large hail and show no roofing permit afterward, and the crew has work for weeks.
A wind event with no hail
Scenario
A squall line passes with strong gusts and no hail. The manager colours homes by wind and filters to 60 mph and up in the affected counties.
Outcome
The team works a wind event with its own list instead of ignoring a storm that hail-only maps would have missed.
Showing a homeowner the date of record
Scenario
A rep meets a homeowner who is unsure which storm to blame for a stain. The rep opens the home panel and reads out the dates and sizes in the storm history.
Outcome
The conversation moves from guessing to a list of dated events, and the rep offers to inspect the roof and document what is there.
Why Choose Hail Map for Roofers: Swaths, Size and Wind Filters?
| Aspect | With Roof Report Pro | Without |
|---|---|---|
| Seeing where a storm hit | Hail swaths and wind zones drawn on the street map | A news radar loop and a hunch |
| Hail size | Presets for 1, 1.5, 2 and 2.5 inches and up | One headline number for a whole county |
| How far back you can look | A window from today to three years, history from October 2020 | Whatever you remember or saved |
| Wind | Presets at 50, 60 and 75 mph and up, plus a zones overlay | Separate sites for wind and for hail |
| From storm to door list | Filter, draw a territory, assign it, export addresses | Screenshots and a hand-built spreadsheet |
| Where it works | Florida and Texas storm layers today | Depends on the tool and its coverage list |
What does the hail layer show?
It shows swaths, which are the paths hail took across the ground, built from radar-based hail size estimates. Each swath carries a size, so a stripe of 2-inch hail looks different from a stripe of 1-inch. You can colour homes by their hail reading, or filter to a size and see only the houses under it. The view is an estimate for an area, so treat it as the shortlist and not as a finding about any single roof.
How do the size presets and time windows work together?
The size preset sets the smallest hail you care about, and the window sets how far back the map looks. A one-week window with the 1.5 inch preset answers a storm that just happened. A three-year window with the 2 inch preset answers a different question, which is where older, larger hail landed. Because both are simple clicks, a manager can try several combinations in a couple of minutes.
How does the wind filter differ from the hail filter?
Wind has three speed presets, 50, 60 and 75 mph and up, and a zones overlay that shows where winds of interest blew. It is a single wind layer rather than separate layers per storm type. The wind filter appears when the wind layer is switched on, in the same panel as hail, so you can stack the two when a storm brought both, or use wind alone for events that brought no hail.
How current is the storm data?
The radar hail and gust data is loaded daily, and the history reaches back to October 2020. That makes it a good fit for the days and weeks after a storm and for older storms alike. It is not a live feed. The live storms view is marked as coming soon, and storm alerts are not available, so open the map after a storm instead of waiting for it to come to you.
What does the map not tell me?
It does not tell you that a roof is damaged, and it does not give a per-house verdict. The map is not a report: a Forensic report carries its own storm and weather section for the date of loss. What it does give you is a map-wide, per-house record of the hail and wind estimated at that address, so your inspector knows which dates to ask about. The roof itself still has to be looked at by a person.
How do I combine storms with roof age and permits?
Add the year-built range and the roof permit filters to your storm filter. A house built decades ago, under large hail, with no roofing permit since the storm, is a stronger prospect than a house built last year. Roof dates are recorded for only a small share of homes, so lean on year built and permits for most of the list, and use the roof age preset when the data is there.
Where is the hail and wind map available?
Florida and Texas today. The storm layers are ready for the two states where house data is live: 67 Florida counties and 241 Texas counties. Georgia, Alabama and Tennessee are next, and Louisiana and Oklahoma come later. If your crew works outside those states, the map cannot place houses under a storm for you yet.
What does a seat cost?
Coverage by state
Florida, Texas
Georgia, Alabama, Tennessee
Louisiana, Oklahoma
None. One seat price whichever states you work.
How it compares
A SalesRabbit alternative for roofers
Compare the commitment, the add-ons and the data behind the map before you sign a multi-year agreement
A Knockio alternative for roofers
Knockio's listed seat price is lower than ours, so here is what a Roof Report Pro seat adds for a roofing company
A Hail Recon alternative with no per-state pricing
Look at how the plan is sold, how long you are tied in and what sits on the map before you pay for a region
A Rhino Recon alternative that does not meter the map
Compare a plan that counts property lookups with one that charges per user and leaves the map unmetered
Canvassing and hail map apps for roofers, compared
The tools on one dated table, sorted by the job each one does, with the cases where another tool is the better fit for your crew
Frequently Asked Questions
Who Benefits Most
Hail Map for Roofers: Swaths, Size and Wind Filters is designed for these professionals.
Built for Storm Damage Inspectors
Process high-volume storm inspections efficiently. AI identifies hail impacts, wind damage, and debris damage fast.
Built for Roofing Contractors
Train your team with a structured inspection checklist. Close deals with professional reports that show the homeowner exactly what was found.
Look at your last big storm on the map
Start a free trial, pick the storm you remember best and filter to its date. You can judge the swath against what you saw on the ground, then draw a territory and send a rep.
Start free trial